# How Many Amps Does A Refrigerator Use? Find Out!

Last Updated on May 22, 2022 by

How Many Amps Does A Refrigerator Use? If you’re thinking about purchasing a new refrigerator, you should know how many amps it consumes because this will affect your electric bill. Unfortunately, that information will not be found in many appliance store brochures or on the refrigerator itself. So, how can you figure out how much electricity your refrigerator consumes? Let’s get started with a little arithmetic and more online browsing to figure out how many amps a refrigerator takes.

Refrigerators typically may use between 3 to 8 amps. To begin, check up on your refrigerator’s model number and seek the handbook. Refrigerators with an energy rating will include power measurements in the instructions. If amps aren’t specified, you’ll have to figure out how many volts and watts it consumes. Next, enter it into a simple formula: divide the watts by the volts to get the result for your refrigerator.

## Concepts Of Amps

The electrical run rate is calculated using an amp. Electrical regulations determine the chain and course top sizes based on the root of amps. A course overload causes the wires to get irritated, resulting in a domino cascade in a shot hazard.

When more than one appliance is connected to the same circuit, the total amps for each job control should be less than the cable and route roller rating.

Refrigerator amps are the total amount of electricity used by a refrigerator compressor to chill the compartment. In the case of 120 V, the amperage varies between 3 and 5 for all home refrigerators.

Because the in-rush amperage is much higher, you’ll need a dedicated 15–20 amp tour. Because the compressor is not operating the whole time, the median amp is small. It is consistent in kWh (kilowatt-hours). It takes a lot of new electricity to open and put a fridge in. After all, the appliance is in its initialization phase, with all systems operational. However, the refrigerator does not just eat what you place in it.

This may also happen while you pause in front of the fridge, distracted with the door open, peering inside with an indecisive regulator.

The refrigerator reacts to close doors or maintains consistent heat throughout an idle night after the ideal temperature is attained. Scenario scenarios include the total amount of energy spent by the appliance.

Look for the manufacturer’s tag on your refrigerator to learn about its power usage. It will also offer you general information, such as the amps required to power your refrigerator. A refrigerator takes roughly 6 or 7 amps in general but quadruples during the start-up surge.

## Is It Safe To Use An Extension Cord To Power A Fridge?

This is a difficult question to answer. Yes, an extension cable can power a refrigerator. It depends on your circumstances and how safe this is. Before you contemplate utilizing an extension cable, you should consider the following:

Is the extension cable capable of providing the electricity that a refrigerator requires? How long do you plan on using the extension cord? You’ll need to know how many amps the refrigerator requires and the extension cord’s wire gauge rating. This knowledge is essential for safely using an extension cable with a refrigerator.

In general, it’s best to avoid utilizing extension cables with high-power equipment. If it is required, be sure it is just temporary. Refrigerators should be connected to an outlet directly if possible. Always proceed with care. You shouldn’t do anything just because you can.

## Do Refrigerators Require a Special Circuit

A separate circuit for a refrigerator is recognized as a best practice in building. A dedicated circuit implies that your refrigerator will be powered by its circuit with its grounding connection. A 6-amp refrigerator may draw up to 15 to 20 amps at peak use. Local electrical regulations recommend a 15 to 20 amp circuit to avoid an electrical overload.

Along with the other circuit breakers on your main panelboard, the power supply outlet for your refrigerator should have its own 20 amp circuit breaker.

When working with residential electrical systems, it’s better to make big allowances for worst-case situations, such as power spikes and surges.

## What Type Of Refrigerator Circuit Breaker Do I Need?

The recommended practice is to use a circuit breaker rated 3 to 4 times the refrigerator’s rated current when determining what kind of circuit breaker to use. Give yourself some breathing space if your electric installation’s power dips. All refrigerators can withstand a slight variation in voltage as long as less than 10% of the nominal level.

As a result, most domestic refrigerators utilize a 15 or 20-amp breaker. If you want to utilize many appliances on the same circuit breaker, pay attention to their amperage.

## What Voltage Is Used By A Fridge?

Fridges exist in various forms and sizes, as well as varied purposes, which influences the voltage rating. Most domestic refrigerators in the United States are rated for 120 volts; however, this allows for 10% fluctuations, and some older refrigerators are rated for 115 volts. This rating discrepancy causes no problems for residents.

Refrigerators in RVs and campers often include gas-electric absorption cooling systems. They do, however, need electric power for operating lights and different controls. They often require 12 volts of electricity for this.

House refrigerators, for example, employ the same freon systems and are often powered by 12 or 24 volts. Various small capacity portable fridges on the market are designed to be powered by a 12-volt vehicle lighter plug.

They are also why you will find these plugs in your vehicle’s trunk and on the central console. Due to the varying practice of declaring it amongst manufacturers, determining how many amps your fridge draws might be difficult.

All refrigerators have two amps ratings: the lower one, which allows your fridge to operate constantly at total capacity, and the starting amperage, which allows the compressor to begin the cooling cycle. This second rating is usually much higher than the first. Depending on the precise make and model, a family refrigerator will draw between 3 and 6 amps throughout the chilling cycle. Many appliances may take up to 15 amps, making them dangerous to operate on the same circuit as a refrigerator.

## Is It Possible To Use One Outlet To Power Two Refrigerators?

In principle, two freezers may be powered by a single outlet. With starting taken into account, the maximum number of amps they need varies from 3 to 12. On the other hand, the beginning is why you should never use one outlet to power two freezers.

A refrigerator’s unexpected activation might occasionally need up to 15 amps. The circuit will trip if two refrigerators are plugged into the same outlet. Two refrigerators will overwhelm a standard 20 amp circuit.

## Is It Safe To Plug A Refrigerator Into A Surge Protector?

Refrigerators, as previously said, go through various procedures. One of these procedures decides if a refrigerator can be plugged into a surge protector. The compressor is the determinant in this situation. A compressor is a refrigerator component that circulates refrigerant throughout the system.

Heat and current overloads may damage this component. It will use a surge to switch off if it begins to overheat or detects a current overload. The system will be restarted. However, it will not reboot if you use a [easyazon_link keywords=”surge protector” locale=”US” tag=”realikal-20″]surge protector[/easyazon_link]. Manufacturers such as General Electric advise against plugging a refrigerator into a surge protector.

## Rated Current

The rated current is the highest continuous amperage at which the refrigerator’s compressor will run. In other words, this is the amperage on the most significant load during the majority of the on-cycle. In the actual world, your refrigerator will use this amount of power when it is turned up to its highest level; otherwise, it will require less power.

The fridge compressor will not surpass this figure under normal circumstances, but it may do so if it is powered by a lower voltage than it is rated for. Components of the compressor’s electric motor may fail in this circumstance.

## Locked Rotor Amperage

When a compressor starts up for the first time, it encounters internal resistance, both electromagnetic and mechanical, due to the inertia of the coolant it must move. The amperage is increased during the first few seconds of the cycle to overcome this.

This greater current is a starting, locked rotor amperage or surges current. This current is usually 2 to 3 times the rated current, but it may be 5 times for certain older refrigerators. As a result, the prudent guideline assumes it to be as much as 6 times the rated power.

## Refrigerator Cycles

Refrigerators function by extracting heat from the inside in their most basic form. Because of the nature of the specific liquids and gasses employed inside them, they do this.

These liquids boil at very low temperatures, much below freezing, allowing their condition to be modified by varying their pressure. The compressor is a component of a refrigerator that does this, and its primary purpose is to raise the pressure of the coolant and transform it into a liquid.

The coolant then runs through the cooling components, exposing it to temperatures over its boiling point, drawing thermal energy from the surrounding environment, and converting it to gas.

## Conclusion on How Many Amps Does A Refrigerator Use?

You can estimate all of your household’s power needs by knowing the principles of watts and amperage. This information is useful when reducing power bill expenditures or preparing to install solar panels. Separate circuits should also be set up for high-powered refrigerators, electric stoves, and electric water heaters.

These dedicated circuits guarantee that no other appliance contributes to the amperage of the high-powered equipment, potentially tripping the circuit breaker.